Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Broadview Park
If your gate is sagging, grinding, or refusing to open in Broadview Park, the culprit is almost always corrosion. Salt-humid air off the Everglades and Atlantic accelerates wear on hinges, tracks, and operator boards faster than inland, and most gate failures here trace back to that. We work on gates across Broadview Park weekly, and we know exactly what the coastal air does to steel, aluminum, and electronics. Our Gate Repair team handles everything from hinge replacement to full automation diagnosis. Call (833) 570-5807 any time to get a specialist out to your property.
Why Miami Gate Company Is Broadview Park’s Preferred Gate Repair Company
We’re a gate-only shop. Gates are all we do, and that focus means our technicians aren’t splitting time between fences, garage doors, and whatever else. When a Broadview Park homeowner calls us about a swing gate that won’t close or a slide gate that binds halfway, we arrive already knowing the local housing stock: mid-century ranchers, aluminum and chain-link yard gates, older operators that have been through a dozen hurricane seasons. Homeowners and property managers along State Road 7 and the residential streets east of US-441 keep calling us back because we diagnose the actual failure, not the symptom. Ruben Castellano, who runs Miami Gate Company, built the business around one principle: fix what you have, not what’s convenient to sell. For Broadview Park specifically, we carry galvanized and stainless hardware that actually survives the salt air.
Our reputation in Broadview Park has been built through years of repeat service calls and referrals between neighbors. When one homeowner on a street off Davie Road has a gate fixed properly, we tend to hear from two more on the same block. That’s how we’ve grown here. We’re familiar with the unincorporated county rules that apply to your property, and we bring that knowledge to every quote. Free estimates always.
Styles & brands we work with
Wrought Iron Gate Repair in Broadview Park
Wrought Iron Gate Repair in Broadview Park means dealing with rust first and alignment second. The ornamental iron gates you see on so many Broadview Park homes from the 1960s and 1970s look strong, but the joints, hinge barrels, and bottom rails are rusting from the inside out in this climate. We remove the gate when needed, cut out rotted sections at the hinge stile or bottom rail, weld in new matching steel, then treat and repaint the entire frame so the patch doesn’t stand out. A typical wrought iron repair in Broadview Park runs $250 to $800 depending on how much metal needs replacing and whether the gate has to come off its posts. If the hinge side is badly corroded, we’ll refit with stainless steel hinge barrels and heavy-duty bearing hinges rated for coastal exposure.
What We Fix on Iron Gates
The hinge stile is the first thing to fail on a wrought iron gate near salt air. Water sits in the lower hinge barrel, rust expands, and the gate starts dragging. We’ve repaired hundreds of these in Broadview Park. We also handle broken scrollwork, snapped pickets, and gates that have been hit by vehicles or storm debris.
Rebuilding vs. Replacing
Not every iron gate is worth saving. If the frame is rusted through in more than two places or the gate has sagged so badly the top rail is bent, replacement is often cheaper than repeated repairs. When we quote a Broadview Park job, we show you both numbers and let you decide. No pressure to replace. In fact, we’d rather repair a well-built wrought iron gate than install something lighter.
Metal Gate Repair in Broadview Park
Metal Gate Repair in Broadview Park covers aluminum, steel, and chain-link gates: the workhorses of this community’s driveways, yards, and light-commercial properties along 441. Aluminum gates corrode differently than steel. They don’t rust through, but the hardware does. Steel gates rust at the welds, the bottom rail, and anywhere the coating has been scratched. We repair metal gates by replacing failing hardware, welding cracks, straightening bent frames, and reinforcing posts that have loosened in the sandy Broward soil. Metal gate repairs in Broadview Park typically range from $180 for a hinge and latch replacement to $1,200+ for structural rebuilding of a long driveway gate.
Hinge & Post Work on Metal Gates
The hinge post is where most metal gate problems start in Broadview Park. The concrete footing settles, the post leans, and the gate starts dragging on the latch side. We re-set posts in new concrete with proper drainage and use stainless or galvanized post hardware so the repair lasts. A post reset usually runs $350 to $600.
Weld & Rust Repair on Steel Gates
Steel gate frames rust from the bottom up. We grind out the rotted metal, weld in new steel plate or tube, then coat the repair area with a zinc-rich primer and rust-inhibiting topcoat. For gates near the Everglades edge of Broadview Park, we’ll often suggest moving to stainless hinges and galvanized latch hardware because the humidity there is worse than the rest of the neighborhood.
Trusted Brands We Service in Broadview Park
We work on virtually any gate system, whatever brand you have. Our technicians are trained across at least nine major gate and operator brands, including DoorKing, Ghost Controls, Mighty Mule, and Elite. That brand-agnostic approach means we diagnose what your system actually needs, not what a single manufacturer incentivizes. For Broadview Park customers, we commonly keep DoorKing and Mighty Mule control boards and remotes on hand so we can complete many repairs on the first visit rather than ordering parts and coming back. If your operator is from LiftMaster, FAAC, BFT, Linear, or Viking, we repair those too. Gates are all we do, and that focus shows in the speed of our diagnosis.
Common Gate Repair Problems We See in Broadview Park Homes
- Hinge post corrosion and footing settlement: The concrete around hinge posts shifts in Broadview Park’s sandy soil, especially after heavy summer rain. Posts lean, gates sag, and latches stop lining up. We fix the post first, then the gate.
- Rack and pinion rust on slide gates: Slide gate tracks sit close to the ground, and that’s exactly where salt humidity and standing water do their work. The rack corrodes, teeth strip, and the gate jams. We replace racks and pinions with galvanized or corrosion-resistant components.
- Operator board degradation from salt-humid air: Control boards inside gate operators don’t like constant moisture. Broadview Park sees more board failures than inland neighborhoods because of the humidity. We install boards with corrosion-resistant coatings where possible and seal enclosures properly.
- Post-storm gate realignment: After a hurricane or strong tropical storm, gates shift on their footings, motors strain, and safety sensors get knocked out of alignment. We handle the realignment, the mechanical repair, and the sensor re-aiming in one visit.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Broadview Park, FL
Gate repair costs in Broadview Park run from about $180 for basic hinge and latch work to $800+ for structural wrought iron or steel repairs. Operator board replacement typically lands between $350 and $650 depending on brand. Full slide gate track replacement with new rack and pinion starts around $500 and can reach $1,200 on longer commercial gates. Post reset work runs $350 to $600 per post. What affects the final number: how much hardware actually needs replacing, gate size and weight, and whether we’re matching existing ironwork. Every quote is written and agreed before any work starts. You’ll know the full price before we touch your gate. Call (833) 570-5807 for a free estimate.
We Also Serve Cities Near Broadview Park
We work throughout central Broward County. Along with Broadview Park, our regular service area includes Fort Lauderdale, Plantation, Broward Estates, and Lauderhill. If your property is a few blocks over the municipal line, call anyway. We cover the surrounding streets, and if you’re in our broader service footprint we’ll get a technician to you just the same.
Serving Broadview Park, FL — Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Broadview Park
Gate hinges fail quickly in Broadview Park because salt-humid air accelerates rust, and the sandy soil allows hinge post footings to shift. The hinge on the post side is under constant load, and once water gets inside the hinge barrel, corrosion starts eating the metal from the inside. We replace hinges with sealed stainless or galvanized hardware rated for coastal conditions. Call (833) 570-5807 if your gate is dragging or the hinges are squealing.
The best gate operator for Broadview Park is one with a corrosion-resistant control board and a sealed enclosure rated for humid, salt-exposed environments. We typically recommend operators from DoorKing, Ghost Controls, or LiftMaster that are designed with coastal durability in mind. The right operator depends on your gate’s weight, swing or slide type, and how often it cycles. We’ll quote you a system that matches Broadview Park’s conditions, not a generic one.
In most cases, repairing existing gate hardware, hinges, or an operator board does not require a permit. But because Broadview Park is unincorporated Broward County, if the repair involves replacement of the gate structure or a new operator, Broward County’s High-Velocity Hurricane Zone rules apply, and replacement products must carry Miami-Dade NOA or Florida product approval. We know which jobs trigger county review and which don’t. Call us before you start the project and we’ll tell you what your specific repair requires.
The best prevention is to have your hinge posts, hinges, and track inspected before hurricane season, and to repair any corrosion or footing movement early. A gate that sags after a storm is usually one that already had weakened hardware or a slowly settling post. We offer pre-season inspections for Broadview Park homeowners, and we’ll tell you honestly whether anything needs attention. A $200 hinge replacement now beats a $900 post reset after the next storm.
Entrapment protection is the set of safety devices, typically photocells or contact edges, that stop an automatic gate from closing on a person, pet, or vehicle. Since 2000, UL 325 requires entrapment protection on all automatic gate operators, including residential systems. It’s a real safety requirement, not an upsell. If your Broadview Park gate operator lacks working photocells or a reversing edge, it’s out of compliance. We check and install these on every automatic gate we service.
Call Miami Gate Company for Gate Repair in Broadview Park
We recently repaired a LiftMaster slide gate on a 1960s ranch home off State Road 7 in Broadview Park. The rack and pinion had corroded, the hinge post footing had settled, and the gate was binding so hard the operator had nearly burned out. We replaced the galvanized track and stainless hinges, re-leveled the post footing, and installed a new LiftMaster operator board with corrosion-resistant coating. We also added a safety photocell to bring the system up to UL 325. That’s typical of the work we do here. If your gate is sagging, grinding, or dead, call (833) 570-5807 for a free estimate. Written price agreed before any work starts.
Written by Ruben Castellano, Owner at Miami Gate Company, serving Broadview Park and central Broward County.