Gate Repair in Hollywood — Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Hollywood

Gate repair in Hollywood comes down to one thing: salt. If your gate is sagging, sticking, or the operator stopped responding, salt air and humidity have likely done more damage than ordinary wear. Miami Gate Company works on gate systems throughout Hollywood every week, from the canal-front streets of 33019 to the HOA communities west toward 33024. We handle the full scope of Gate Repair work, including hinges, posts, welds, operators, and control boards. Call (833) 570-5807 and we’ll send a technician who knows what Hollywood’s coastal conditions do to gate hardware.

Call (833) 570-5807

Why Miami Gate Company Is Hollywood’s Preferred Gate Repair Company

Gates are all we do. That focus means our technicians diagnose problems faster because they’ve seen the failure modes hundreds of times. When a Hollywood homeowner calls about a gate that won’t open after a summer squall, we’re already thinking salt corrosion on the control board, not guessing. Ruben Castellano built Miami Gate Company as a brand-agnostic gate specialist, which means we work across competing operator platforms rather than pushing one manufacturer. For Hollywood residents, that translates to a repair based on what your system actually needs.

We service the full spectrum of Hollywood housing: mid-century block homes east of I-95 with original manual swing gates, and the master-planned communities toward 33026 and 33027 with shared automatic entry gates. We know the repair profiles of both. A sagging wrought iron gate on a 1960s single-family lot needs different work than a failed safety loop on a 40-home HOA entry. Same specialist, same day or next, same phone number: (833) 570-5807.

Our Hollywood customers call us because we show up ready. No thirty-minute preamble about which brands we sort of know. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your gate has a name on it, we’ve likely fixed that model in Hollywood this month.

Wrought Iron Gate Repair in Hollywood

Wrought Iron Gate Repair in Hollywood is our most common residential call, and for good reason: the city’s older neighborhoods are full of original iron gates from the 1950s through the 1970s, and salt air near the Intracoastal attacks them relentlessly. In Hollywood, wrought iron fails from the ground up. A typical repair on a single-driveway iron gate in Hollywood runs $250 – $650 depending on whether we’re rebuilding hinges, cutting out a rotted post section, or repairing multiple rust-through points on the pickets.

The Footing Corrosion Problem

Most Hollywood wrought iron gates don’t fail because the iron is old. They fail because the hinge post rots through right at the concrete footing, where salt-laden groundwater wicks up into the steel. The panel looks fine, but the gate drags on the driveway or won’t latch. We cut out the rotted section and set a new galvanized core before re-welding the post, which is the only repair that lasts more than a season or two this close to the water.

Rust Through Pickets and Rails

When salt spray pits the lower rail of an iron gate, you see flaking paint and orange streaks bleeding onto the concrete. If we can repair rather than replace, we sandblast the affected section, weld in new steel where needed, and prime with a zinc-rich coating before painting. On canal-front homes in 33019, we recommend stainless fasteners on every piece we touch. Painted steel hardware simply won’t hold up.

Metal Gate Repair in Hollywood

Metal Gate Repair in Hollywood covers aluminum driveway gates, steel pool gates, and the long shared entry gates at HOA communities. Aluminum gates in Hollywood’s coastal zones pit and seize at the hinge points because of galvanic corrosion between dissimilar metals. A typical metal gate repair in Hollywood runs $200 – $550 for hinge replacement and realignment, and $400 – $900 when we’re replacing a rusted post or repairing storm-damaged sections.

Aluminum Gate Seized Hinges

Aluminum is everywhere in Hollywood because it resists rust, but it corrodes differently. Salt air causes aluminum hinge barrels to weld themselves to steel pins through galvanic action. When an aluminum gate won’t move at all, this is usually why. We drill out the old pin, install stainless pins and bushings, and the gate swings like new.

Steel Gate Post Replacement and Welding

Steel gates on Hollywood waterfront properties take a beating. Storm surge and salt spray eat through the base of the post within a few years, and once the post moves, the gate sags no matter how much you tighten the hinges. We replace the post with galvanized steel, weld it square, and then address whatever hinge damage the movement caused. On a canal-front lot off Northlake Drive in 33019, we rebuilt a sagging wrought iron swing gate whose hinge post had rusted through at the footing. We replaced the post with a galvanized core, switched to stainless hinges, and sealed the LiftMaster operator board that had corroded from salt spray. The gate now swings clean and the operator has survived two squall seasons without a callback.

Trusted Brands We Service in Hollywood

We work on virtually any gate system, whatever brand you have. In Hollywood we most often see LiftMaster and FAAC on residential drives, DoorKing on commercial and HOA entries, and Ghost Controls and Mighty Mule on newer retrofit installs. Elite and Linear operators show up throughout the city’s condo and apartment communities. Brand-agnostic means we fix what you have. We’re not here to sell you a system you don’t need. We keep common boards, sensors, and remotes stocked for fast turnaround so a Hollywood repair doesn’t stall waiting on a part from a warehouse.

Common Gate Repair Problems We See in Hollywood Homes

• Sagging gates from corroded hinge posts. The post rusts through at the concrete footing, usually within ten to fifteen years of installation in salt-exposed areas. By the time the gate drags, the post base is often gone entirely.
• Operators failing after storms. Lightning and power surges during Hollywood’s summer squalls fry control boards, and buried low-voltage loop detectors short out when canal-front lots flood. The operator is often fine; the board and wiring are not.
• False safety sensor trips from salt film. Photocells near the Intracoastal get a fine salt haze that triggers false obstructions and erratic gate behavior. A proper cleaning and seal works; the sensor usually doesn’t need replacing.
• Stuck-open or stuck-closed gates on shared entries. HOA communities in western Hollywood depend on a single operator and safety loop. When one component fails, the whole entry bricks. These repairs need to be fast because every resident is locked out or locked in.

Pricing for Gate Repair in Hollywood, FL

We Also Serve Cities Near Hollywood

Our Gate Repair in Hollywood team covers the city and runs calls into Andover, Carver Ranches, Miramar, and West Park. If you’re near the Hollywood line in any of those communities, the same technicians, same brands, and same salt-aware repair approach apply. Call (833) 570-5807 and tell us where you are.

FAQs About Gate Repair in Hollywood