Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Jensen Beach
When an electric gate stops working in Jensen Beach, it’s rarely a small problem. Salt air off the Indian River Lagoon corrodes operator internals, humidity shorts control boards, and storm-season wind knocks gate leafs out of alignment. We see it constantly, and we fix it. Miami Gate Company sends gate specialists, not general handymen, to Jensen Beach, FL. We work on the motor, the board, the wiring, the sensors, and the hinges, and we diagnose the actual failure instead of guessing. Call (833) 570-5807 for a free estimate, and we’ll tell you straight whether your gate needs a retrofit or a replacement.
Why Miami Gate Company Is Jensen Beach’s Preferred Electric Gate Repair Company
Jensen Beach gate systems age differently than inland Martin County systems. The barrier island and lagoon-front lots in 34957 and 34958 put gates through constant salt spray, driving rain, and hurricane-force wind. Ruben Castellano built Miami Gate Company around that reality. We’re a gate-only shop. That focus means our technicians carry the specific control boards, hinge kits, and corrosion-resistant hardware that Jensen Beach properties actually need, not a truck full of unrelated tools.
Our electric gate repair work in Jensen Beach covers everything from older LiftMaster operators on 1970s canal homes to newer Ghost Controls and DoorKing systems in gated communities off Jensen Beach Boulevard. We don’t push a single brand. We service the system you already own, which matters when your gate predates modern safety photoeye requirements but still runs fine mechanically. Local homeowners and property managers call us because we give them an honest read on what’s worth fixing and what isn’t.
Styles & brands we work with
Electric Gate Motor in Jensen Beach
Electric gate motor repair in Jensen Beach usually comes down to two failure modes: salt corrosion eating the motor windings and capacitor, or storm surge and heavy rain shorting the power feed. A failed motor may hum without moving, trip its breaker, or run intermittently when humidity spikes. On waterfront streets like Skyline Drive or Sailfish Road, we expect to find corroded terminals and rusted mounting bolts even on gates that look clean from the outside.
When to Repair vs. Replace
If the motor housing is intact and the gear train still turns freely, we can often rebuild it with new bearings, seals, and a capacitor, which runs $280 to $520 in Jensen Beach. If salt water has reached the windings, repair is usually false economy. A new swing or slide gate motor for a residential driveway here runs $750 to $1,400 installed, depending on gate weight and access.
Post-Storm Motor Recovery
After a nor’easter or hurricane, we see motors that run but won’t move the gate. That’s frequently water in the limit switch or a stripped gear from the gate being forced open by wind. We pull the unit, dry and clean the control cavity, and replace the limit switch and any corroded connectors. That’s a common $240 to $390 repair on older Jensen Beach operators.
Gate Access Control in Jensen Beach
Gate access control in Jensen Beach means more than the keypad by the mailbox. It’s the full loop: the keypad or card reader, the loop detector in the driveway, the safety photoeyes, and the control board that ties them together. On Jensen Beach barrier island properties, salt spray and floodwater take out loop detectors first. The wire connections oxidize, the detector stops sensing the vehicle, and the gate won’t open automatically.
Keypad and Intercom Failures
Surface-mount keypads on ocean-side and lagoon-side homes last two to five years before the membrane cracks and salt finds the contact grid. We replace them with sealed stainless-face units and re-terminate the wiring with dielectric grease. A new keypad for a Jensen Beach gate runs $180 to $340 installed. If the intercom or telephone entry system is failing on a multi-home gate, we test the phone line first, then the control board relay, which is often the corroded culprit.
Loop Detector and Photoeye Problems
Flooded driveway loops are a Jensen Beach staple. After heavy rain or surge, the detector reads continuously or not at all. We often install a new saw-cut loop with marine-grade wire, which costs $350 to $600 here. Photoeyes on older gates get misaligned by wind and coated with salt film; cleaning and realignment is a $95 to $150 service call, but if the lens is etched by sand and salt, replacement is the only real fix.
Trusted Brands We Service in Jensen Beach
We’re brand-agnostic by design, and that matters on the Treasure Coast. Jensen Beach has a huge mix of gate hardware because different builders and condo associations specified different systems over the decades. We service Ghost Controls and Mighty Mule systems common on newer residential installs, plus DoorKing and Elite operators found on HOA entrances and estate properties. We keep common control boards, remotes, and photoeye kits ready for Jensen Beach jobs so we’re not waiting a week for a part. Whatever brand you have, we know it. Electric gate repair is our Electric Gate Repair specialty, and we order directly from each manufacturer’s parts network rather than relying on generic substitutes.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Jensen Beach Homes
- Corroded hinge posts and fasteners: Salt air off the lagoon and ocean degrades galvanized steel within three to five years on waterfront properties. Gates start sagging, then scrape the driveway or bind against the latch. We replace posts and hardware with stainless or marine-grade coated steel and realign the gate leafs.
- Obsolete control boards: Older LiftMaster and Linear boards from the late 1990s and early 2000s are failing from humidity and power surges. Replacement boards for those models are often discontinued. We can sometimes retrofit a current board into the old housing; other times the operator needs replacing.
- Saturated wooden posts after storm season: Jensen Beach has a lot of mid-century and 1970s-80s homes where wooden privacy gates are hung on pressure-treated posts set decades ago. Saturated posts twist and rot at the footing, throwing the gate out of square. We reset them in concrete and reinforce the hinge points.
- Waterlogged safety sensors and loop detectors: Even a mild tropical storm can leave photocells and loop detectors underwater in low-lying island and riverside lots. The system either refuses to close, or the gate stays open indefinitely. We test each component, dry what’s salvageable, and replace what’s shorted.
Pricing for Electric Gate Repair in Jensen Beach, FL
Expect the following real-world numbers for Jensen Beach gate work. A service call and diagnosis runs $95 to $150. Basic repairs like cleaning a salt-filmed photoeye or adjusting a limit switch fall in the $120 to $220 range. A new swing-gate motor installed runs $750 to $1,400. Full access-control retrofits, meaning keypad, loop detector, photoeyes, and control board, land between $900 and $1,800 for a single driveway. Commercial HOA gate systems in Jensen Beach run higher based on gate size and traffic frequency. We quote the full price up front, you approve it before any work starts, and the number on the invoice matches the number you approved. No surprises. Call (833) 570-5807 for a free estimate on your specific gate.
We Also Serve Cities Near Jensen Beach
Our Jensen Beach gate repair routes also cover Hutchinson Island South, Sewall’s Point, North River Shores, and Stuart. If your property sits in one of those areas, we’ll bring the same salt-corrosion and storm-wind expertise we use across Jensen Beach daily. Same gate specialists, same straight answers.
Serving Jensen Beach, FL — Our Local Coverage Area
We’re based in the Jensen Beach area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Jensen Beach
You can usually retrofit the operator without replacing the entire gate, as long as the frame and hinges are still sound. We reset the gate on new pressure-treated or steel-reinforced posts, swap the rotted hinge-point blocking, and then mount the new or rebuilt operator. If the gate itself is sagging beyond the point where realignment holds, replacement becomes the cheaper long-term answer. Call (833) 570-5807 and we’ll assess it for free.
Salt-laden onshore air and storm-driven water get inside the operator housing and attack the motor, capacitor, control board, and wiring terminals. Corrosion causes shorts, rusted mounts cause misalignment, and the constant humidity keeps everything damp. Inland Martin County systems last noticeably longer because they’re not getting hit with the same salt load. That’s why we use sealed enclosures, dielectric grease on every connection, and stainless or marine-grade fasteners on every Jensen Beach repair.
First check whether the circuit breaker for the gate is on, then look at the photoeyes; they’re likely misaligned or waterlogged after the storm. Misaligned photoeyes will keep the gate from closing. If the keypad is dead but the breaker is on, water likely shorted the keypad wiring or the control board input. Don’t open the control panel if you see standing water or corrosion; call (833) 570-5807 and we’ll diagnose the entire system, not just the obvious part.
It depends on the board and the operator. If we can source a tested replacement or a drop-in retrofit board, repair makes sense and typically runs $350 to $700. If the board is discontinued and the motor and gear train are also near end of life, a new operator is the better use of your money. In Jensen Beach’s salt environment, we lean toward replacement when the housing itself is corroded; putting a new board inside a rusted cabinet just delays another failure. We’ll give you the honest numbers either way.
Older gates often lack current safety photoeyes or have single-edge safety sensors that don’t meet modern standards. They can usually be added without replacing the gate. We install through-beam photoeyes across the gate opening, add a reversing edge or secondary entrapment sensor, and confirm the operator’s auto-reverse function works. This is a common retrofit on Jensen Beach homes built in the 1970s and 80s, and it runs $300 to $700 on most residential gates. Call (833) 570-5807 for a free quote.
Written by Ruben Castellano, Owner at Miami Gate Company, serving Jensen Beach and the Treasure Coast.